How the turret moves, why the housing is laid out the way it is, and which dimensions come from catalogues rather than measured parts.
Pan — the servo gear (32T, module 1.5) turns the
turntable’s gear (16T) in the opposite direction at twice the angle,
centre distance 36 mm. A turntable angle φ ∈ [−180°, 180°] maps to the
servo angle 90 − φ/2. The servo’s end stops are the only
travel limit, so the hose and cables twist by at most one turn.
Pan bearing — the 608ZZ sits in the turntable’s hub, above its gear, and turns on a fixed 8 mm pin that rises from the cover. The pin’s head is split in two and has a 0.35 mm lip: it flexes while the inner race passes over it and then holds the turntable down. A shoulder under the inner race carries the head’s weight; a ledge in the hub bears on the outer race only. The hub’s pocket clears the bearing by 0.2 mm; six crush ribs up its wall, 0.15 mm proud of the outer race, hold it, since a plain press-fit bore prints too tight with the 0.6 mm nozzle. The ribs stop 1 mm under the bearing’s top, so the bearing first sits square on the bore.
Tilt — direct drive on the tilt servo, limited in firmware to −60° (down) … +60° (up). The tilt arm hangs on the servo horn on the left and turns on a printed 8 mm stub in an open-top slot of the right upright. The arm goes in first and the servo last, its spline pushed sideways into the horn; then the spline holds the left side and a spacer 0.4 mm from the right upright stops the arm from sliding off it.
Home position — with the turntable at 0° the nozzle
points toward +Y. The firmware converts a sensor azimuth α (0° = +X
wall, counter-clockwise from above) into the turntable angle
φ = α − 90°.
Spray — the six fixed sensors give the fire’s direction only coarsely, and nothing measures its distance, so a thin jet would usually miss. The fitted nozzle spreads a flat horizontal fan (cat-eye orifice: a V-groove cut into the domed end of the bore) that covers the pan error, and the firmware sweeps the tilt up and down while the pump runs to cover the unknown distance. The R385 is too weak to atomize water: a mist would carry only a few centimetres.
Proportions — the spray must clear the housing when the nozzle aims down, so the footprint is small and the tilt axis high: 126 × 100 mm, tilt axis 73 mm above the cover. The spray axis clears the cover’s edge down to 43° below the horizontal in the worst direction (toward a corner) and to 49° and 55° across the short and long sides; the turntable’s bowl rim, which turns with the nozzle, stops it first, at 37.5° in every direction. The housing is taller instead (tank 50 mm, deck 90 mm).
| Layout | Footprint | Tilt axis above the cover | Steepest aim clearing the cover (worst direction) |
|---|---|---|---|
| tank under the deck (fitted) | 126 × 100 mm | 73 mm | 43° |
| tank beside the deck | ~126 × 145 mm | 73 mm | 38° |
A tank beside the deck saves a storey but widens the footprint by the tank’s thickness, and the wider footprint limits the downward aim; with the tank under the deck the footprint stays at what the pump and battery need.
No screws in the housing — the tank and deck join with a lip, a groove and silicone. The cover drops onto two locating pins and four snap tongues in the deck walls click over its edge: one on each of the ±Y walls, one on each X wall in the −Y half, each on a stretch of wall that the top sensor row leaves free. Pulling a tongue outward releases its side. The tongues are strips of wall freed by two slots and thinned to 1.6 mm, 21 mm long to the hook, so they flex the 1 mm the hook needs at about 0.5 % strain.
Filling — the tank’s spout leaves its −X end at 45°, rises outside the deck wall and ends above the tank’s top, so the tank fills up to the deck floor (about 540 ml). The suction hose’s collar in the deck floor stands higher than the spout’s mouth, so a full spout cannot overflow into the deck.
Sealing — the turret moves, so every path from the water to the deck is closed:
The housing is not rainproof: the sensor collars, USB slot, switch and tongue slots stay open.
The deck splits into a pump/battery half (+Y) and an electronics half (−Y).
checks/interference.py loads
STEP/assembly.step and tests every pair of parts for
overlap at pan −180°, −90°, 0°, 90°, 180° and tilt −60°, 0°, +60°.
Designed contacts (bearing press fit, pan pin through the bearing, servo
ears, nozzle in its ring, headers on the board, battery on its tray,
plug in the spout) are whitelisted. It also confirms the gear centre
distance and the running gap between the gears (0.28 mm at pan 0°).
These parts were modelled from catalogue or typical values, not from the actual stock:
| Part | Assumed size | Effect of a deviation |
|---|---|---|
| R385 pump | 90 mm long, 40 × 40 mm head, Ø27.6 mm motor | held by zip ties; the tray sits 1 mm above the head, so a taller
head needs TRAY["z"] raised |
| Hose | 3/16” ID × 5/16” OD (4.76 × 7.94 mm), measured | suction collar Ø8.34, breather clip and plug socket squeeze it 0.15 mm per side |
| Relay module | 50 × 26 × 19 mm | lies on two tie bridges |
| XL4015 buck | 54 × 23 × 16 mm | lies on two tie bridges; must stay 3 mm under the perfboard |
| HX-2S-D01 BMS | 41 × 16 × 3.5 mm | pocket has 0.5 mm clearance per side |
| Perfboard | 50 × 70 mm, 18 × 24 holes at 2.54 mm | snap mount; check before printing the deck |
| Flame sensor module | 14 × 34 mm PCB | stands on a 30 mm ledge, hot-glued |
| Dual 18650 holder | 77 × 41 × 21 mm | sits between the tray’s end stops |
| Mini rocker switch | ~10 × 15 mm lip, 8.8 × 13.2 mm cutout | change SWITCH_CUTOUT if the switch does not snap
in |
| RP-SMA bulkhead | 1/4”-36 thread, Ø6.6 mm teardrop hole | connector body inside, washers and nut outside clamp the 2.4 mm wall |
The MG90S follows the SG90 outline measured on the step.parts model;
the 608ZZ and the dual-18650 holder come from step.parts
(STEP/imported/).