The parts print on five plates for a Bambu Lab P1S with a 0.6 mm hardened steel nozzle in PLA, with tree supports from the build plate; the turntable plate supports only its servo window.
scripts/slice.sh slices the tank, deck, head, turntable
and coupler plates with the presets in print/presets/
(Bambu Lab P1S 0.6 nozzle, 0.24 mm Optimal @BBL P1P 0.6, Bambu PLA Basic, Textured PEI
Plate: bed at 55 °C and the start G-code’s −0.04 mm Z offset for the
texture) plus the per-plate overrides below, and writes
gcode/plate_<name>.gcode.3mf.
| Plate | Parts | Overrides | Time | Filament |
|---|---|---|---|---|
| tank | tank | 4 walls, 13 bottom / 5 top layers, 100 % infill (watertight) | 1 h 48 min | 112 g |
| deck | deck, battery tray | 3 walls, 8 bottom / 5 top layers, 20 % infill | 4 h 04 min | 205 g |
| head | cover, servo gear, tilt arm, fill plug, flat-fan nozzle | 3 walls, 40 % infill | 1 h 47 min | 72 g |
| coupler | hose coupler (bench tests only) | 3 walls, 100 % infill, 5 mm brim | 11 min | 1 g |
| turntable | turntable | 3 walls, 40 % infill, 0.20 mm layers, outer/inner walls at 60/80 mm/s, overhangs from 10 % at 40 mm/s, 8 s minimum layer time, travel inside the part, retraction on every travel over 1 mm, nozzle at 215 °C after the first layer, scarf seam on the outer wall; normal snug support only in the enforcer, not limited to the build plate | 1 h 23 min | 30 g |
gcode/*.gcode.3mf files open in OrcaSlicer with these
settings and the plate’s overrides marked as changed; the raw plates in
3MF/plates/ open with OrcaSlicer’s own defaults.SWITCH_CUTOUT in
src/lib/params.py, rebuild and re-slice the deck.PB["size"] and re-slice.HOSE_ID and HOSE_OD (4.76 × 7.94 mm, 3/16” ×
5/16”). For another hose, change both and re-slice.Open each .gcode.3mf in Bambu Studio or Bambu Connect
and send it to the printer. In the print dialog, confirm the nozzle (0.6
mm, hardened steel) and the plate type that is actually on the printer.
Printing the tank first allows a leak test with water before anything
else is assembled.
| Part | Orientation | Reason |
|---|---|---|
| tank, deck | floor down | walls print as continuous perimeters; the tank’s fill spout grows out of the wall at 45° and needs no support |
| battery tray | flat | plate with low end stops |
| cover | underside down | pan pin and servo bosses rise from the plate |
| servo gear | horn recess down | recess needs no bridge |
| turntable | gear down | hub, 60° bowl and uprights rise without overhangs; a support enforcer in the servo window carries its 23 mm top bridge from the window’s sill, since a support from the bed would climb through the bore and leave blobs on the bowl; the bearing pocket opens upward |
| tilt arm | standing on a 20 mm end face | ring, ribs and plates print without overhangs; the pivot stub prints as a short horizontal cylinder |
| fan nozzle | tip up | the orifice prints vertically; the V-groove has 30° flanks |
| fill plug | knob down | the O-ring groove’s upper flank is 45° |