Everything the turret needs besides the printed parts. Prices and shops are tracked in the project shopping list; this page lists what each part is for.
| Part | Script | Plate |
|---|---|---|
| Tank, ~540 ml, 45° fill spout and 4 external M3 mounting tabs | src/tank.py |
tank |
| Electronics deck (its floor closes the tank), snap tongues for the cover | src/deck.py |
deck |
| Battery tray, snaps in above the pump | src/battery_tray.py |
deck |
| Cover with the pan pin, pan servo pocket and raised hose hole | src/cover.py |
head |
| 32T pan gear on the servo horn | src/servo_gear.py |
head |
| Turntable: 16T gear, bearing hub, 60° bowl and tilt uprights in one part | src/turntable.py |
turntable |
| Tilt arm with pivot stub and nozzle clamp ring | src/tilt_arm.py |
head |
| Flat-fan nozzle, 2.6 × 0.8 mm slit, 3/16” hose barb | src/nozzle_fan.py |
head |
| Fill plug with O-ring groove and breather socket | src/fill_plug.py |
head |
| Straight 3/16” hose coupler, to extend the suction hose to an outside reservoir on the bench | src/hose_coupler.py |
coupler |
| Part | Qty | Use |
|---|---|---|
| ESP32 DevKit V1, 30 pins, ESP32-WROOM-32U module | 1 | controller, plugs into the perfboard |
| 2.4 GHz antenna, RP-SMA with U.FL pigtail | 1 | WiFi: the WROOM-32U has no built-in antenna; mounts through the −X wall |
| IR flame sensor module (AO, GND, VCC, DO) | 6 | one per wall collar, 60° apart |
| GY-521 IMU module (MPU-6050), with its right-angle header | 1 | measures the base’s tilt so the aim stays level on uneven ground or on a carrier |
| MG90S micro servo, 180° | 2 | pan (under the cover) and tilt (on the turntable) |
| Servo extension cable, 15 cm | 1 | tilt servo, reaches the board through the cover hole |
| R385 diaphragm pump, 6–12 V | 1 | water |
| 1-channel relay module, 5 V coil | 1 | switches the pump |
| 1N4007 diode | 1 | flyback diode across the pump |
| 2N2222A NPN transistor | 1 | relay driver: pulls the relay’s IN to GND while D26 is high |
| Resistor 1 kΩ, 1/4 W | 1 | relay driver, base resistor |
| Resistor 10 kΩ, 1/4 W | 1 | relay driver, holds the transistor off while the ESP32 boots |
| XL4015 buck module, 4–38 V in | 1 | 5 V for ESP32, servos and relay |
| HX-2S-D01 BMS, 2S 8 A | 1 | over-discharge, over-charge and short-circuit protection |
| 18650 cells | 2 | 2S pack, 6.0–8.4 V |
| 2 × 18650 holder (series) | 1 | battery tray |
| 2-bay 18650 charger | 1 | charges the cells out of the holder |
| Mini snap-in rocker switch, ~10 × 15 mm front lip | 1 | main power, −Y wall (8.8 × 13.2 mm cutout) |
| Perfboard 5 × 7 cm (18 × 24 holes) | 1 | controller board |
| Female header strip, 40 pins | 1 | cut into 2 × 15 for the ESP32 |
| Male header strip, 40 pins | 1 | cut into 2 × 3 for the servo connectors |
| Dupont jumpers female–female, 20 cm | 21 | one per relay and sensor wire, cut to length: the plug end goes on the module’s pin |
| Silicone wire 22 AWG (red, black, orange) | ~1 m | power wiring |
| Silicone wire 30 AWG (assorted) | ~1 m | board jumpers and signals |
| Heat-shrink tubing | — | every soldered wire-to-wire or wire-to-tab joint |
| Part | Qty | Use |
|---|---|---|
| 608ZZ bearing | 1 | pan axis, pressed into the turntable’s hub |
| Servo ear screw (included with each MG90S) | 4 | servos to the cover bosses and to the turntable’s left upright |
| Horn centre screw (included with each MG90S) | 1 | pan gear onto the pan servo spline; the tilt servo’s stays spare |
| Self-tapping screw for plastic, 2 × 6 mm (not included) | 4 | servo horns into the 32T gear (2) and into the tilt arm (2) |
| Zip ties, ≤ 4 mm wide, ≥ 150 mm long | 8 | pump (2), battery holder (2), buck (2), relay (2) |
| Zip ties, ≤ 2.5 mm wide | 3 | hose ends on the pump’s two barbs and the nozzle’s barb |
| Hose, 3/16” ID × 5/16” OD (4.76 × 7.94 mm) | ~0.6 m | pump inlet to tank floor, pump outlet to nozzle, breather |
| O-ring, 13 mm ID × 17 mm OD (2 mm cross-section), rubber | 1 | fill plug seal; the spout bore is sized for it |
| Neutral silicone sealant | — | tank lip and deck groove seam, suction collar, cover’s hose hole |
| Silicone grease (optional) | — | fill plug O-ring |
| M3 screws (optional) | 4 | tank tabs to a base plate or a carrier |
Joints — the printed parts join without screws: the tank and deck with a lip, a groove and silicone; the cover with two locating pins and four snap tongues; the turntable with a snap pin through the bearing; the tilt arm with a stub in an open-top slot; the nozzle with three crush ribs in its ring; perfboard and battery tray with lips and snap hooks. Only the servos use screws.
Servo screws — each MG90S comes with three screws: two for its ears and one centre screw for the horn. The four 2 × 6 mm screws that fix the horns into the gear and the arm are bought separately; they bite into 1.6 mm pilots, and the horn’s middle holes may need a 2 mm drill for them to pass. The ear screws bite into 1.8 mm pilots.
Hose — the 3/16” ID hose stretches over the R385’s barbs and the nozzle’s barb; dip its end in hot water to push it on, and it grips as it cools. The suction collar and the breather clip are sized for its 5/16” OD with little clearance. Silicone hose bends tighter without kinking, which matters for the outlet hose’s curve in the deck corner.